#Remove molex connector from fan manual#
#Remove molex connector from fan free#
#Remove molex connector from fan crack#

The major issue I have is these 2 fans are my CPU fans connected to my waterblock and the CPU fan headers on my board are in a janky place where I can't get to without removing almost the entirety of my water cooling loop so if I were to ditch the fan controller then I either have to drain my loop and pull it all out so I can get to the fan headers behind the rad or remove 2 other fans and plug the CPU fans into those headers leaving me with only 3 of my 5 fans connected and a problem with negative pressure inside my case. With that said, you should definitely use a good quality adaptor, molex by standard can carry more current than SATA power plug so if you have a good quality PSU and a good quality adaptor theres.

We recommend using these 20-24 AGW Micro-Fit 3.0 female crimp pins to insert your wire into the plug properly. Remember back in the day when 6 pin wasnt a thing for most PSUs, cards like GTX750Ti usually shipped with a molex to 6 pin adaptor.

#Remove molex connector from fan crack#

My solution was to crack open the casing and remove all 4 wires then insert them into the molex connector so they are just sticking in the holes which is working great however I am obviously concerned about how long I can keep them like that without causing damage to my system via a short. One of our most popular top-pin Molex connector pin-and-socket connectors is this Micro-Fit 3.0, 2 position 3mm plug-type connector. These connectors are small and it's tough to securely attach your wires to them without a) buying a adapter yourself or b) go Rambo on it and solder the thing.The plastic housing of the molex connector for the fan controller built into my case came apart and 2 of the wires were no longer secured in the housing, as soon as I tried to plug them into a molex on my PSU 2 of the wires would pop out of the back instead of going into the plug. It's harder to connect to the motherboard as you may guess. You can read signal or CHA_FAN_SPEED on the manual. So, any adapter that can 'convert' your fans Molex male connector into. Your fans are most like the older style 3-pin fans that are controlled by the Voltage supplied to it from a mobo header. You are after a 3-pin connector on the motherboard with the following setup: Signal-12V-Ground. Process of identifying Molex connectors, unplugging and or cutting said wire (s) and then replacing said fan or fans. A PWM fan has a different find of motor than the ones your case came with, and that is why it can use a PWM signal. JRready ST5253-04 is a comprehensive connector. Both fans have standard molex 4 pin connectors that connect to the psu, but they also have a 3rd wire with a high and low switch(low does nothing, high is unbearably loud).

#Remove molex connector from fan manual#

Read the instruction manual and check the available connections. Molex Micro-Fit 3.0 Terminal Release Tool & 3P 4P PC Fan Connector Pin Extractors for Computer Maintenance. What's easier than this?įinally, what you have been waiting for: As for our motherboard So you just hooked your first 3-wire fan to a 4-wire molex.

Bend the tip of the exposed wire, producing a tiny U shape.

Remove the isolation of the end of both the Red and Black wires, thus exposing a little of the metal wire beneath.

I'm explaining the more difficult and leaving a note on the easier:

#Remove molex connector from fan free#

Instead of fiddling around the motherboard you can splice the fan wiring with a free 4 or 3 pin molex adapter coming of your power supply unit. It is very easy to remove wires from FAN connectors: You will only need a small screwdriver, scissor, knife or similar small device with a thin tip. Check the image on the link you provided again :)Īnyways, feeling adventurous? Here it is: Well, you do need 12V for the fan to really kick.